Guide to Update Galaxy Note 10.1 WiFi N8010 to XXUCMA5 Android 4.1.2 Jelly Bean

Abdullah Saad
Posted Jan 26, 2013
14Shares
Share Tweet Submit

Samsung Galaxy Note 10.1 Wi-Fi N8010 has now officially received an update; XXUCMA5 Android 4.1.2 Jelly Bean Official Firmware. The new release comes around the same time when Samsung is releasing software updates for almost its entire product line up, all at the same time. While you are likely to receive the update via OTA update process or KIES. . If for some reason, you cannot access the official update or would like not to wait and get it on your tablet right now, here is a guide to update your Galaxy Note 10.1 WiFi N8010 to XXUCMA5 Android 4.1.2 Jelly Bean firmware.

Disclaimer:This guide will use a tool; Odin to flash the official firmware on your Galaxy S3 I9300. During the process, you might lose all your existing installed apps and personal settings. It is therefore necessary for you to follow the guide carefully. Also, please, do mind that this tutorial is only for Galaxy Note 10.1 WiFi N8010. Don’t try this guide in any other Android device.

Android 4.1.2 XXUCMA5 Firmware Details:

PDA: N8010XXUCMA5
CSC: N8010OXACMA5
Version: 4.1.2
Date: 2013-01-14
Regions: Austria, Belgium, France, Germany, Hungary, Italy, Spain, United Kingdom

Download

  1. Android 4.1.2 N8010XXUCMA5 for Galaxy Note 10.1 N8010
  2. Odin 3.07

Guide to Update Galaxy Note 10.1 WiFi N8010 to XXUCMA5 Android 4.1.2 Jelly Bean

  1. Extract the firmware zip file that you have downloaded using the link above, you will then get a .tar file alongside other files.
  2. Extract Odin zip file to get Odin3 v3.07.exe.
  3. Power off your phone. Wait 5-6 seconds to confirm complete switch off.
  4. Put the Galaxy Note 10.1 WiFi N8010 in Download Mode by pressing and holding Volume Down and Power button until Samsung Galaxy logo appears in tablet screen. Wait for a few seconds and you will be in download mode.
  5. Run Odin3 v3.07.exe (see Step 2) as an Administrator.
  6. Connect your Galaxy Note 10.1 WiFi N8010 with your PC using USB cable. A message will appear under Odin’s message box in the bottom left saying “Added!!”. If you don’t get it, then try another USB port. If that too doesn’t work, then reinstall the USB driver. If you successfully see the “Added!!” message in Odin, you are good to go. Also, check for COM port with a number in Yellow to make sure that you have successfully added your device.
  7. Select the following files in Odin at their respective tabs from extracted XXUCMA5 firmware folder :
    • Click the ‘PDA’ Button, and select the .tar file here with *code* appearing in file-name.
    • Click the ‘Phone’ Button, and select file with *modem* in its name (Ignore, if this file does not file exist).
    • Click the ‘CSC’ Button, and select file with *csc* in its name (Ignore, if this file does not file exist).
    • Click the ‘PIT’ Button, and select the .pit file. Use only if you got it while extracting in step 1 above, otherwise ignore it.
    • In Odin window, make sure Auto Reboot and F. Reset Time checkboxes are selected. Please make sure that Re-Partition checkbox is selected, only if you are using a .pit file (see Step 7.4).
  8. Recheck everything mentioned in Step 7 & 8 above. Hit the ‘START’ button to begin the flashing process.
    Once the flashing process is completed, the tablet will reboot automatically and you will see a PASS message in the top-left-most box. You can now unplug the USB cable to disconnect your device from computer.

If you have followed every point described in the guide, your Galaxy Note 10.1 WiFi N8010 should now be running Android 4.1.2 Jelly Bean build N8010XXUCMA5. If there are any issues, feel free to post in the comments section for our staff to take a look at it.

Share Tweet Submit